Get 300-710 Braindumps & 300-710 Real Exam Questions
Cisco 300-710 Actual Questions and Braindumps
Cisco 300-710 certification exam is an intermediate-level exam that focuses on securing networks with Cisco Firepower. 300-710 exam is designed to test a candidate's knowledge and skills related to implementing and managing advanced security features on Cisco Firepower and Firepower Threat Defense platforms. 300-710 exam covers a wide range of topics, including firewall configuration, intrusion prevention, network access control, and advanced malware protection.
NEW QUESTION # 153
A network engineer must provide redundancy between two Cisco FTD devices. The redundancy configuration must include automatic configuration, translation, and connection updates. After the initial configuration of the two appliances, which two steps must be taken to proceed with the redundancy configuration? (Choose two.)
- A. Configure the standby IP addresses.
- B. Ensure the high availability license is enabled.
- C. Configure the failover link with stateful properties.
- D. Configure the virtual MAC address on the failover link.
- E. Disable hellos on the inside interface.
Answer: A,C
NEW QUESTION # 154
What are two application layer preprocessors? (Choose two.)
- A. ICMP
- B. SSL
- C. IMAP
- D. CIFS
- E. DNP3
Answer: B,C
Explanation:
https://www.cisco.com/c/en/us/td/docs/security/firepower/60/configuration/guide/fpmc-config- guide-v60/Application_Layer_Preprocessors.html
NEW QUESTION # 155
In which two ways do access control policies operate on a Cisco Firepower system? (Choose two.)
- A. They can block traffic based on Security Intelligence data.
- B. Traffic inspection can be interrupted temporarily when configuration changes are deployed.
- C. File policies use an associated variable set to perform intrusion prevention.
- D. The system performs a preliminary inspection on trusted traffic to validate that it matches the trusted parameters.
- E. The system performs intrusion inspection followed by file inspection.
Answer: A,B
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/60/configuration/guide/fpmc-config- guide-v60/Access_Control_Using_Intrusion_and_File_Policies.html
NEW QUESTION # 156
Which limitation applies to Cisco FMC dashboards in a multi-domain environment?
- A. Child domains are not able to view dashboards that originate from an ancestor domain.
- B. Child domains have access to only a limited set of widgets from ancestor domains.
- C. Child domains are able to view but not edit dashboards that originate from an ancestor domain.
- D. Only the administrator of the top ancestor domain is able to view dashboards.
Answer: A
Explanation:
Section: Management and Troubleshooting
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/60/configuration/guide/fpmc-config-guide- v60/Using_Dashboards.html
NEW QUESTION # 157
An organization has noticed that malware was downloaded from a website that does not currently have a known bad reputation. How will this issue be addresses globally in the quickest way possible and with the least amount of impact?
- A. by denying outbound web access
- B. by creating a URL object in the policy to block the website
- C. Cisco Talos will automatically update the policies.
- D. by Isolating the endpoint
Answer: C
NEW QUESTION # 158
An administrator is adding a new URL-based category feed to the Cisco FMC for use within the policies.
The intelligence source does not use STIX. but instead uses a .txt file format.
Which action ensures that regular updates are provided?
- A. Upload the .txt file and configure automatic updates using the embedded URL.
- B. Add a URL source and select the flat file type within Cisco FMC.
- C. Convert the .txt file to STIX and upload it to the Cisco FMC.
- D. Add a TAXII feed source and input the URL for the feed.
Answer: B
Explanation:
TID supports additional intelligence ingestion methods - With both Security Intelligence and TID, you can import threat intelligence into the system by either manually uploading flat files or configuring the system to retrieve flat files from a third-party host. TID provides increased flexibility in managing those flat files. In addition, TID can retrieve and ingest intelligence provided in Structured Threat Information eXpression (STIX™) format.
Flat File
Files must be ASCII text files with one observable value per line
https://www.cisco.com/c/en/us/td/docs/security/firepower/622/configuration/guide/fpmc-config- guide-v622/threat_intelligence_director_tid.pdf
NEW QUESTION # 159
An engineer has been tasked with providing disaster recovery for an organization's primary Cisco FMC. What must be done on the primary and secondary Cisco FMCs to ensure that a copy of the original corporate policy is available if the primary Cisco FMC fails?
- A. Configure high-availability in both the primary and secondary Cisco FMCs
- B. Connect the primary and secondary Cisco FMC devices with Category 6 cables of not more than
10 meters in length. - C. Restore the primary Cisco FMC backup configuration to the secondary Cisco FMC device when the primary device fails
- D. Place the active Cisco FMC device on the same trusted management network as the standby device
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config- guide-v62/firepower_management_center_high_availability.html
NEW QUESTION # 160
When do you need the file-size command option during troubleshooting with packet capture?
- A. when capture packets exceed 32 MB
- B. when capture packets exceed 10 GB
- C. when capture packets are less than 16 MB
- D. when capture packets are restricted from the secondary memory
Answer: A
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config-guide-v62/troubleshooting_the_system.html
NEW QUESTION # 161
A network engineer implements a new Cisco Firepower device on the network to take advantage of its intrusion detection functionality. There is a requirement to analyze the traffic going across the device, alert on any malicious traffic, and appear as a bump in the wire How should this be implemented?
- A. Enable routing on the Cisco Firepower
- B. Add an IP address to the physical Cisco Firepower interfaces.
- C. Configure a bridge group in transparent mode.
- D. Specify the BVl IP address as the default gateway for connected devices.
Answer: C
Explanation:
Traditionally, a firewall is a routed hop and acts as a default gateway for hosts that connect to one of its screened subnets. A transparent firewall, on the other hand, is a Layer 2 firewall that acts like a "bump in the wire," or a "stealth firewall," and is not seen as a router hop to connected devices. However, like any other firewall, access control between interfaces is controlled, and all of the usual firewall checks are in place.
Layer 2 connectivity is achieved by using a "bridge group" where you group together the inside and outside interfaces for a network, and the ASA uses bridging techniques to pass traffic between the interfaces. Each bridge group includes a Bridge Virtual Interface (BVI) to which you assign an IP address on the network. You can have multiple bridge groups for multiple networks.
In transparent mode, these bridge groups cannot communicate with each other.
https://www.cisco.com/c/en/us/td/docs/security/asa/asa97/configuration/general/asa-97-general- config/intro-fw.html
NEW QUESTION # 162
A network administrator notices that inspection has been interrupted on all non-managed interfaces of a device. What is the cause of this?
- A. Multiple inline interface pairs were added to the same inline interface.
- B. The value of the highest MTU assigned to any non-management interface was changed.
- C. A passive interface was associated with a security zone.
- D. The value of the highest MSS assigned to any non-management interface was changed.
Answer: B
Explanation:
Changing the highest MTU value among all non-management interfaces on the device restarts the Snort process when you deploy configuration changes, temporarily interrupting traffic inspection. Inspection is interrupted on all non-management interfaces, not just the interface you modified. Whether this interruption drops traffic or passes it without further inspection depends on the model of the managed device and the interface type. See Snort Restart Traffic Behavior for more information.
https://www.cisco.com/c/en/us/td/docs/security/firepower/60/configuration/guide/fpmc-config- guide-v60/fpmc-config-guide-v60_chapter_01101010.html
NEW QUESTION # 163
While integrating Cisco Umbrella with Cisco Threat Response, a network security engineer wants to automatically push blocking of domains from the Cisco Threat Response interface to Cisco Umbrella. Which API meets this requirement?
- A. investigate
- B. reporting
- C. enforcement
- D. REST
Answer: C
Explanation:
The Umbrella Enforcement API is a feature that allows for automated addition of new domains to a security enforcement list.
NEW QUESTION # 164
An engineer is setting up a new Firepower deployment and is looking at the default FMC policies to start the implementation During the initial trial phase, the organization wants to test some common Snort rules while still allowing the majority of network traffic to pass Which default policy should be used?
- A. Maximum Detection
- B. Security Over Connectivity
- C. Balanced Security and Connectivity
- D. Connectivity Over Security
Answer: C
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/security/firepower/623/fdm/fptd-fdm-config-guide-623/fptd-fdm-intrusio
NEW QUESTION # 165
Drag and drop the steps to restore an automatic device registration failure on the standby Cisco FMC from the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION # 166
A user within an organization opened a malicious file on a workstation which in turn caused a ransomware attack on the network. What should be configured within the Cisco FMC to ensure the file is tested for viruses on a sandbox system?
- A. Spere analysis
- B. Capacity handling
- C. Dynamic analysis
- D. Local malware analysis
Answer: C
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/security/firepower/623/configuration/guide/fpmc-config-guide-v623/file_policies_and_advanced_malware_protection.html#ID-2199-000005d8
NEW QUESTION # 167
Which firewall design will allow It to forward traffic at layers 2 and 3 for the same subnet?
- A. transparent mode
- B. Cisco Firepower Threat Defense mode
- C. routed mode
- D. Integrated routing and bridging
Answer: A
Explanation:
Transparent mode is a firewall configuration in which the firewall acts as a "bump in the wire" or a "stealth firewall" and is not seen as a router hop to connected devices. In transparent mode, the firewall can forward traffic at both layer 2 and layer 3 for the same subnet, as it does not perform any address translation or routing. The firewall inspects the traffic and applies security policies based on the source and destination IP addresses, ports, and protocols. Transparent mode is useful when you want to deploy a firewall without changing the existing network topology or addressing scheme1.
NEW QUESTION # 168
......
300-710 Dumps To Pass Cisco Exam in 24 Hours - SurePassExams: https://dumpsninja.surepassexams.com/300-710-exam-bootcamp.html