300-510 Exam Dumps Pass with Updated Jul-2023 Tests Dumps
300-510 exam questions for practice in 2023 Updated 177 Questions
To prepare for this exam, candidates should have a solid understanding of networking fundamentals, including TCP/IP, routing protocols, and network security. They should also have experience with Cisco routing and switching technologies, as well as with service provider technologies such as Carrier Ethernet, Provider Backbone Bridging, and Multiprotocol Label Switching (MPLS). The Cisco 300-510 exam is part of the Cisco Certified Network Professional Service Provider (CCNP Service Provider) certification track and is a requirement for obtaining the CCNP Service Provider certification.
NEW QUESTION # 69
Refer to the exhibit
Router R1 is configured to advertise outgoing SA messages to routers R2 and R3, but to receive incoming SA messages only from R2. Which additional configuration must an engineer apply to router R1 so it filters all MSDP SA messages from Domain-C?
- A. R3# ip msdp password peer 192.168.1.1
- B. R1# ip msdp password peer 192.168.3.1
- C. R3# ip msdp sa-filter out 192.168.3.1
- D. R1# ip msdp sa-filter in 192.168.3.1
Answer: D
NEW QUESTION # 70
Refer to the exhibit.
Refer to the exhibit. Network connectivity between bank A and bank B has been lost Users at bank A and bank B are able to successfully reach their directly connected PE routers. All routers in OSPF area 0 are correctly advertising and learning routing updates. Which action resolves the issue?
- A. Enable next-hop-self under the iBGP peering configuration on routers PEI and PE2
- B. Configure the P routers to redtstnbute BGP routes within OSPF area 0.
- C. Configure router PI to advertise the IP prefix of PEI.
- D. Configure MPLS with an end-to-end label-switched path on each router.
Answer: D
NEW QUESTION # 71
Refer to the exhibit.
CE1 and CE2 cannot communicate through the service provider BGP peering is established between PE1 and PE2. IS-IS is the only routing protocol running in the service provider core. What step can be done to troubleshoot the issue?
- A. Switch the IGPs running in the core from IS-IS to OSPF to support a Cisco MPLS TE tunnel from PE1 to PE2.
- B. Configure BGP between CE and PE routers.
- C. Verify the MPLS LSPs.
- D. Confirm that IS-IS is running with metric-style narrow.
Answer: C
NEW QUESTION # 72
Refer to the exhibit.
Routers R1, R2. R3, and R4 have been configured to run OSPF. and router R5 is running EIGRP Traffic from R1 to R5 is expected to pass via R4. but OSPF routing has calculated the best path via R3. Which action corrects the problem?
- A. Configure R1 with a static route to the R5 networks and set R5 as the next hop.
- B. Change the metric-type value on R3 to 2.
- C. Configure R3 to use metric-type 1 with a higher metric than R4.
- D. Reconfigure R1 in Area 0.
Answer: B
NEW QUESTION # 73
Refer to the exhibit.
Refer to the exhibit There is a BGP traffic path issue between Customer-1 and Customer-2 Users from Customer-2 have reported file transfer issues High utilization on the path between both customers causes many packet drops. Which configuration resolves the issue?
- A. Option D
- B. Option C
- C. Option B
- D. Option A
Answer: C
NEW QUESTION # 74
Compare different features between OSPFv2 and OSPFv3. Drag and drop the descriptions of OSPF from the left onto the correct OSPF versions on the right.
Answer:
Explanation:
NEW QUESTION # 75
Refer to the exhibit. A service provider technician is working on a multicast issue for a customer.
While checking the multicast table, the technician notices that no flags are present for the (1.1.1.1, 239.1.1.1) entry, yet flags are present for the (1.1.1.1, 232.1.1.1) entry.
Which factor might explain this issue?
- A. Only ASM is permitted
- B. Only the default SSM range is permitted
- C. Only the administratively scoped range is permitted
- D. Only GLOP is permitted
Answer: B
NEW QUESTION # 76
Refer to the exhibit. R1 is directly connected to R2 and R3. R1 is in BGP AS 123, R2 is in BGP AS 2, and R3 is in BGP AS 3.
Assume that there is no connectivity issue between R1, R2 and R1, R3.
Which result between BGP peers R1, R2 and R1, R3 is true?
- A. The BGP session comes up between R1 and R2 and between R1 and R3.
- B. The BGP session does not come up between R1 and R2 and between R1 and R3.
- C. The BGP session comes up between R1 and R3, but not between R1 and R2.
- D. The BGP session comes up between R1 and R2, but not between R1 and R3.
Answer: D
NEW QUESTION # 77
Refer to the exhibit.
Which LSA type is indicated by this router output?
- A. type 1 LSA
- B. type 4 LSA
- C. type 3 LSA
- D. type 2 LSA
Answer: A
NEW QUESTION # 78
Which statement about enabling segment routing for IGPs is true?
- A. Segment routing can be enabled only under the routing process
- B. Segment routing must first be enabled globally and then under the routing process
- C. Segment routing must first be enabled under then routing process and then globally
- D. Segment routing can be enabled only globally
Answer: B
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/seg_routing/configuration/xe-16-6/segrt-xe-16-6- book/sr-ospfv2-node-sid.html
NEW QUESTION # 79
Refer to the exhibit. A network engineer has divided AS into confederations. Due to repeated ASN, when the 10.0 0.0/8 prefix from R1 arrives to R2, BGP automatically rejects it.
What should the engineer do to fix the problem so that BGP allows that prefix on R2?
- A. Configure the command as-override on R2.
- B. Configure the command as-override on R1.
- C. Configure the command allowas-in on all the PE routers.
- D. Configure the command allowas-in on R2.
Answer: D
Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/112236-allowas-in- bgp-config-example.html
NEW QUESTION # 80
Refer to the exhibit.
Refer to the exhibit. Excessive routes are flooding from network 150.0.0.0 into AS100. Internet traffic between AS400 and AS300 is working normally. No route controlling mechanism is applied on incoming and outgoing traffic Which configuration resolves the issue?
- A. Option D
- B. Option A
- C. Option C
- D. Option B
Answer: B
NEW QUESTION # 81
Refer to the exhibit.
Routers RA and RB are IS-IS peers configured for NSF but router RC is an IS-IS peer without NSF capability If RA undergoes processor switchover what is the effect on the network environment?
- A. All peer relationships remain up, but the link-state database is rebuilt on each device
- B. All peer relationships remain up and the link-state database is unchanged
- C. If RC is operating without the Cisco configuration option only 2 routers tear down their peering relationships and re-establish peering
- D. If RC is operating without the Cisco configuration option all three routers tear down their peering relationships and re-establish peering
Answer: A
NEW QUESTION # 82
Which difference must an engineer consider when choosing whether to implement OSPF or IS-IS as the routing protocol on the network?
- A. To support fast convergence, OSPF uses the LSA arrival timer and IS-IS uses the PRC-interval timer.
- B. IS-IS links are associated with either a Level 1 area or a Level 2 area at one time, but OSPF links are associated with multiple areas at one time.
- C. IS-IS supports ordinary, stub, totally-stub, and NSSA areas, but OSPF supports only stub areas.
- D. The OSPF DR election process is deterministic, and the IS-IS DS election process is not deterministic.
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_isis/configuration/15-s/irs-15-s- book/irs-fscnt.html
NEW QUESTION # 83
Refer to the exhibit.
Which statement about this configuration is true?
- A. Router 1 sends and receives multiple best paths from neighbor 192.168.1.1
- B. Router 1 receives only the best path from neighbor 192.168.1.1
- C. Router 1 sends up to two paths to neighbor 192.168.1.1 for all routes
- D. Router 1 receives up to two paths from neighbor 192.168.1.1 for all routes in the same AS
Answer: A
NEW QUESTION # 84
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network.
Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)
Answer:
Explanation:
NEW QUESTION # 85
Refer to the exhibit.
How are packets directed through the data plane when SRv6 is implemented?
- A. A stack of labels represents an ordered list of segments
- B. The MPLS data plane is used to push labels onto IGP routes
- C. The packet is encapsulated with a header and trailer encoding the ordered list of segments
- D. An ordered list of segments is encoded in a routing extension header
Answer: D
NEW QUESTION # 86
......
The Cisco 300-510 exam is a certification exam that is intended for professionals who are interested in demonstrating their level of knowledge and expertise in implementing Cisco Service Provider Advanced Routing Solutions. This exam is designed to assess the ability of candidates to configure, troubleshoot, and optimize service provider network infrastructures. It is also meant to validate the skills of candidates in implementing Layer 3 services and technologies, such as VPN services, MPLS, BGP, and OSPF.
Authentic 300-510 Dumps With 100% Passing Rate Practice Tests Dumps: https://dumpsninja.surepassexams.com/300-510-exam-bootcamp.html